What does PC mean on a Samsung washer?

PC means: Clutch position / clutch hall signal error. The most likely parts involved are clutch assembly, shift actuator / position sensor.

How much does it cost to fix PC?

A typical motor system repair (motor / sensor / shifter) costs about $285–$550 nationally, parts and labor included. This is a reference range, not a quote — local prices vary.

Can I keep using my washer with a PC code?

Usually the washer will stop and not finish the cycle. Running it again and again while the clutch is not shifting can cause more wear, so it is best to stop using it until it is checked.

Why is there water left in my tub after the PC code?

The washer may have stopped before it could shift into spin to drain. To remove the water, follow the drain steps in your owner's manual, and keep towels on the floor in case of spills.

Error codes › Washer › Samsung

Samsung Washer PC Error Code

Clutch position / clutch hall signal error

Applies to: Top-Load models with clutch/splutch assembly. May also appear as PE, PC1, PE1.

What's going on

The PC code on a Samsung top-load washer means the clutch did not shift properly between washing (agitating) and spinning. The washer checks the clutch position with a sensor, and when the signal is wrong, it stops and shows PC. A simple power reset may clear a one-time glitch, but if the code comes back, a qualified appliance technician is needed.

Many Samsung top-load washers use a clutch assembly, sometimes called a splutch, to switch between two jobs. In one position, the motor moves the wash plate or agitator to wash clothes. In the other, it spins the whole tub to drain water out of the load.

A shifter moves the clutch between these positions, and a position sensor tells the control board where the clutch is. If the board does not get the signal it expects after a shift, it shows PC. This protects the washer from trying to spin or agitate while the clutch is stuck in between.

This code applies to top-load models that have a clutch or splutch assembly. Codes can mean different things on different model generations, so confirm with your washer's model number and the owner's manual.

Likely causes

clutch assembly — If the clutch is worn, damaged, or stuck, it may not move fully into the wash or spin position. The sensor then reports the wrong position, and the washer stops with PC.
shift actuator / position sensor — The shift actuator moves the clutch, and the position sensor reports where it is. If either part fails or sends a bad signal, the control board cannot confirm the shift and shows the code.

The same code can mean different things on different model generations. Check the model number on your washer's rating plate before ordering parts.

Can you fix it yourself?

Not a DIY repair. This one needs a technician with the right tools and parts.

Safe things to check first

Turn the washer off, then unplug it or switch off its breaker for a few minutes. Plug it back in and try a short cycle like Rinse and Spin to see if the code returns.
Check that the load is not too large or too heavy. Remove some items if the tub is packed full, and redistribute the clothes evenly.
Listen during the cycle for grinding, clicking, or repeated whirring when the washer tries to change from washing to spinning. Note what you hear so you can tell the technician.
Make sure the washer is level and not rocking. Do not remove any panels or try to reach the clutch or sensor yourself.

When to call a technician

If the PC code comes back after a power reset, call a qualified appliance technician. Replacing the clutch assembly or shift actuator is not a do-it-yourself repair.

What the repair usually costs

$285–$550

Motor system repair (motor / sensor / shifter), parts and labor — national reference range

Confidence: medium (based on 2 cost guides). Plus a service call fee of about $50–$100, often credited toward the repair.

This is not a quote. Prices vary by region and by model.

Repair or replace?

It depends on age. This repair can cross $500, about half the price of a typical new washer. If yours is near the end of a typical 10–15 year lifespan, compare replacement prices before booking a repair.

A typical new washer costs about $700–$1,300.

Check your washer — free, 2 minutes

Common questions

What does PC mean on a Samsung washer?: PC means: Clutch position / clutch hall signal error. The most likely parts involved are clutch assembly, shift actuator / position sensor.
How much does it cost to fix PC?: A typical motor system repair (motor / sensor / shifter) costs about $285–$550 nationally, parts and labor included. This is a reference range, not a quote — local prices vary.
Should I repair or replace my washer?: It depends on age. This repair can cross $500, about half the price of a typical new washer. If yours is near the end of a typical 10–15 year lifespan, compare replacement prices before booking a repair.
Can I fix PC myself?: Not a DIY repair. This one needs a technician with the right tools and parts.
Can I keep using my washer with a PC code?: Usually the washer will stop and not finish the cycle. Running it again and again while the clutch is not shifting can cause more wear, so it is best to stop using it until it is checked.
Why is there water left in my tub after the PC code?: The washer may have stopped before it could shift into spin to drain. To remove the water, follow the drain steps in your owner's manual, and keep towels on the floor in case of spills.